|
|
楼主 |
发表于 2013-3-7 22:18
|
显示全部楼层
【更新】
如一楼所述，装好以后转向助力失效，ESP 失效，因为转向角传感器不兼容。发动机和方向盘模块有错误，原因是定速巡航手柄型号不可靠，其实也是不兼容。
这两天费劲周折，买到了相匹配的Schleifring和定速巡航手柄。Teilenummer分别为：
Schleifring：1K0 959 653 C 未更换前型号：1K0 959 653
手柄：1K0 953 513 G 未更换前型号：1K0 953 513 A
新的手柄还多了资格取消键。小插曲就是，当中自以为1K0 953 513 F的手柄就应该兼容，买回来一装发现还是不能用，太郁闷了，还好不是私人卖家买的，果断退之，可惜邮费要自己承担，唉，又交学费了！
安装完后，要对转向助力进行角度传感器匹配，和Anschlag匹配，方法网上能有找到，复制如下：
Sensor for Steering Angle (G85)
Important Note: This applies only for Models with Conti/Teves MK70 ABS/ASR. For Conti/Teves MK60 ABS/ASR/ESP look at Vehicle specific specific Procedures in ABS System documentation.
Prerequisites:
Start the vehicle.
Turn the steering wheel one turn to the right and one turn to the left.
Drive in a short distance straight line on a level surface at a speed not higher than 20 km/h.
If the steering wheel is straight during the test drive then stop the vehicle with the wheels pointed straight.
Ensure that the steering wheel is not moved again.
Keep the engine running and do not switch off the ignition.
System voltage at least 12.0 V.
[Select]
[44 - Steering Assist]
[Coding-II - 11] or if that function is not available then use [Sec.Access - 16] instead
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 1 should say "OK".
[Done, Go Back]
To make sure the basic setting was succesful, check the sensor again.
[Measuring Blocks - 08]
Group 007
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]
[Close Controller, Go Back - 06]
Note: After successful basic setting, the Steering Limit Stop needs to be adapted too.
Special Procedures
Steering Limit Stop Adaptation
(Engine still running)
Center steering wheel (±10°) and hold it centered for 5 seconds.
Turn steering wheel completely to the left and hold it there for a second.
Turn steering wheel completely to the right and hold it there for a second.
Center steering wheel (±10°).
Switch OFF engine and ignition.
Switch ON ignition.
Wait 5 seconds.
Steering Assist Warning Lamp should turn OFF. If it doesn't, perform a short test drive.
If the 02546 - Steering Limit Stop 005 - No or Incorrect Basic Setting / Adaptation fault will not clear after driving the vehicle and completing the VW Golf (1K) Steering Assist procedure, increase the time in-between key cycles to 30 seconds or more.
操作完的一瞬间，方向盘变轻了，方向盘警告灯灭了，ESP灯灭了，世界清静了。后来还把转向助力的模式改成了运动模式，禁止状态方向盘更轻，行驶过程中方向盘回复力量更大。发现居然还有个GTI模式，试了下，感觉助力不轻快，拖泥带水的感觉，还是运动模式比较爽朗。
自此，这方向盘改装终于是彻底成功了。毫无后遗症！！ |
|
发表于 2013-3-4 20:59
